pl:install
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revision | Next revisionBoth sides next revision | ||
pl:install [2012/08/21 21:39] – bomb3r | pl:install [2012/08/21 21:52] – bomb3r | ||
---|---|---|---|
Line 64: | Line 64: | ||
* Jeśli używasz kart **SD/ | * Jeśli używasz kart **SD/ | ||
- | * Jeśli używasz kart **SDXC**, albo wolisz pominąć etap aktualizacji firmware' | + | * Jeśli używasz kart **SDXC**, albo wolisz pominąć etap aktualizacji firmware' |
+ | ====== Aktualizacja Magic Lantern ====== | ||
+ | |||
+ | * **Aby zaktualizować ML ze starszej wersji do v2.3, sformatuj swoją kartę (karty), jeśli trzeba zaktualizuj firmware aparatu, wypakuj na kartę pliki ML i przygotuj ją by była boot' | ||
+ | * Sprawdź stronę [[http:// | ||
+ | * Aby zainstalować wersję beta, po prostu wypakuj (lub skopiuj) zmodyfikowane pliki Magic Lantern na kartę i nadpisz stare. | ||
+ | |||
+ | ====== Odinstalowanie Magic Lantern ====== | ||
+ | |||
+ | {{ : | ||
+ | **Nie usuwaj tylko plików ML z karty! Jeśli tak zrobisz, aparat zawiesi się przy uruchamianiu i konieczne będzie wyjęcie baterii.** | ||
+ | |||
+ | ===== Odinstalowanie ML z jednej karty ===== | ||
+ | |||
+ | * Sformatuj kartę z poziomu aparatu (wybierz opcję: //Format card, **remove** Magic Lantern//) i uruchom ponownie. Aparat włączy się z oryginalnym softem. | ||
+ | |||
+ | ===== Odinstalowanie ML z aparatu ===== | ||
+ | |||
+ | * With a Magic Lantern card, launch the **Firmware Update** process and follow the instructions on-screen. | ||
+ | * Re-installing Canon firmware will **not** remove Magic Lantern. | ||
+ | ====== Troubleshooting ====== | ||
+ | |||
+ | * **If the card LED blinks continuously after running Firmware Upgrade**, you don't have the right Canon firmware version or sub-version. To fix it, install the official Canon firmware upgrade from [[# | ||
+ | * **If the screen does not turn on, but autofocus works**, remove the battery and format the card. This happens when the card is bootable, but autoexec.bin is not there. | ||
+ | * **Check if all doors are closed.** The camera will not boot if any of the card or battery doors are open ! | ||
+ | * **If the camera does not boot** (seems dead), **remove the battery and the card**. Then put the battery back and try to boot the camera without card. Then put a formatted card in the camera and try to boot **without** Magic Lantern. Only after you are sure the camera is OK, you can try to see what's wrong with Magic Lantern. | ||
+ | * **If the camera asks for a firmware update**, place Canon firmware on the card (this was a problem in older versions). | ||
+ | * **DO NOT use a bootable card without a working autoexec.bin on it!** If you do, remove the battery immediately, | ||
+ | * Check the [[https:// | ||
+ | |||
+ | ====== Important notes ====== | ||
+ | |||
+ | * **After opening the card door, always wait for LED confirmation (or for 5 seconds) before removing the card!!!** (no such problem on 550D) | ||
+ | * **[[http:// | ||
+ | * If you have a bootable card and have the '' | ||
+ | * If you encounter a " | ||
+ | * When in doubt, remove the battery and reboot. | ||
+ | * **And, remember that this software can damage or destroy your camera.** |
pl/install.txt · Last modified: 2012/08/22 22:25 by bomb3r