it:install
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
it:install [2012/08/16 06:11] – [Step 3. Magic Lantern first startup] scrax | it:install [2012/08/30 14:21] – [Molto Importante] scrax | ||
---|---|---|---|
Line 17: | Line 17: | ||
===== Molto Importante ===== | ===== Molto Importante ===== | ||
- | * Magic Lantern v2.3 usa una leggermente | + | * Magic Lantern v2.3 usa una **struttura |
* After opening the card door, **always wait for LED confirmation** (or for 5 seconds) before removing the card!!! During that period, Canon firmware **accesses the card without turning on the LED**, and if you remove the card too early, the camera will freeze and will drain the battery. Exception: 550D users don't have to wait. | * After opening the card door, **always wait for LED confirmation** (or for 5 seconds) before removing the card!!! During that period, Canon firmware **accesses the card without turning on the LED**, and if you remove the card too early, the camera will freeze and will drain the battery. Exception: 550D users don't have to wait. | ||
- | |||
====== Get the right camera firmware version ====== | ====== Get the right camera firmware version ====== | ||
Line 25: | Line 24: | ||
Firmware updates in general can damage your camera. Read the section in your camera manual before updating your firmware. If you are not comfortable with the risks, stop reading and delete the software before you are tempted to try running it on your camera. | Firmware updates in general can damage your camera. Read the section in your camera manual before updating your firmware. If you are not comfortable with the risks, stop reading and delete the software before you are tempted to try running it on your camera. | ||
- | Magic Lantern v2.3 works **only** with the following camera | + | Magic Lantern v2.3 funziona |
{{page>: | {{page>: | ||
- | You can check your firmware | + | E' possibile verificare la versione del firmware |
Nothing bad will happen if you try to run ML on a different firmware version - the card LED will start blinking and you'll have to take the battery out. Magic Lantern checks firmware version before attempting to run. | Nothing bad will happen if you try to run ML on a different firmware version - the card LED will start blinking and you'll have to take the battery out. Magic Lantern checks firmware version before attempting to run. | ||
- | ====== | + | ====== |
===== Step 1. Preparazione fotocamera ===== | ===== Step 1. Preparazione fotocamera ===== | ||
Line 98: | Line 97: | ||
* Check the [[https:// | * Check the [[https:// | ||
- | ====== | + | ====== |
- | + | ||
- | * **After opening the card door, always wait for LED confirmation (or for 5 seconds) before removing the card!!!** (no such problem on 550D) | + | |
- | * **[[http:// | + | |
- | * If you have a bootable card and have the '' | + | |
- | * If you encounter a " | + | |
- | * When in doubt, remove the battery and reboot. | + | |
- | * **And, remember that this software can damage or destroy your camera.** | + | |
+ | * **Dopo aver aperto lo sportello della scheda, attendi sempre la conferma LED (o per 5 secondi) prima di rimuovere la scheda!!!** (non necessario con 550D) | ||
+ | * **[[http:// | ||
+ | * Se hai una scheda SD avviabile e la '' | ||
+ | * Se ti capita di avere la fotocamera bloccata, **rimuovi la batteria al più presto**. | ||
+ | * Se in dubbio, rimuovi la batteria e riavvia. | ||
+ | * **E ricorda che questo software può danneggiare o distruggere la tua macchina fotografica.** |
it/install.txt · Last modified: 2012/09/05 09:57 by luix90