it:install
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
it:install [2012/08/16 05:46] – scrax | it:install [2012/08/30 14:21] – [Molto Importante] scrax | ||
---|---|---|---|
Line 17: | Line 17: | ||
===== Molto Importante ===== | ===== Molto Importante ===== | ||
- | * Magic Lantern v2.3 usa una leggermente | + | * Magic Lantern v2.3 usa una **struttura |
* After opening the card door, **always wait for LED confirmation** (or for 5 seconds) before removing the card!!! During that period, Canon firmware **accesses the card without turning on the LED**, and if you remove the card too early, the camera will freeze and will drain the battery. Exception: 550D users don't have to wait. | * After opening the card door, **always wait for LED confirmation** (or for 5 seconds) before removing the card!!! During that period, Canon firmware **accesses the card without turning on the LED**, and if you remove the card too early, the camera will freeze and will drain the battery. Exception: 550D users don't have to wait. | ||
- | |||
====== Get the right camera firmware version ====== | ====== Get the right camera firmware version ====== | ||
Line 25: | Line 24: | ||
Firmware updates in general can damage your camera. Read the section in your camera manual before updating your firmware. If you are not comfortable with the risks, stop reading and delete the software before you are tempted to try running it on your camera. | Firmware updates in general can damage your camera. Read the section in your camera manual before updating your firmware. If you are not comfortable with the risks, stop reading and delete the software before you are tempted to try running it on your camera. | ||
- | Magic Lantern v2.3 works **only** with the following camera | + | Magic Lantern v2.3 funziona |
{{page>: | {{page>: | ||
- | You can check your firmware | + | E' possibile verificare la versione del firmware |
Nothing bad will happen if you try to run ML on a different firmware version - the card LED will start blinking and you'll have to take the battery out. Magic Lantern checks firmware version before attempting to run. | Nothing bad will happen if you try to run ML on a different firmware version - the card LED will start blinking and you'll have to take the battery out. Magic Lantern checks firmware version before attempting to run. | ||
- | ====== | + | ====== |
- | ===== Step 1. Preparing your camera | + | ===== Step 1. Preparazione fotocamera |
- | * Fully charge your battery; | + | * Ricarica la batteria finché piena |
- | * Remove any accessories from your camera | + | * Rimuovi ogni eventuale accessorio dalla fotocamera |
- | * For first install, use a simple | + | * Assicurati di avere una scheda |
- | * Make sure you have a card reader. | + | * Assicurati di avere un lettore schede. |
- | * Double-check your Canon firmware | + | * Ricontrolla che la versione del firmware |
- | * Rotate your mode dial to **Manual | + | * Posizionate la rotellina in posizione |
- | * Recommended: Restore your camera | + | * Raccomandato: Ripristinate le impostazioni di fabbrica della camera ('' |
- | + | ===== Step 2. Installazione | |
- | ===== Step 2. Installation | + | |
{{ : | {{ : | ||
- | * Format the card **in the camera** (low-level format). | + | * Formattare la scheda SD **dalla fotocamera** (basso livello, dal menu '' |
- | * Unzip **all** of the files from Magic Lantern zip archive to the **root** of your card. | + | * Decomprimere |
- | * Launch the **Firmware | + | * Avviare il processo di **Aggiornamento |
- | * If the card LED is blinking for more than a few seconds, **upgrade your Canon firmware** | + | * Se il LED della scheda lampeggià per più di alcuni secondi, **aggiornate il vostro |
- | * Once you see the **green confirmation screen**, restart your camera. Done. | + | * Una volta visualizzata la **schermata verde di conferma**, riavviare la macchina fotografica. Fatto. |
- | * If something goes wrong, **check the [[# | + | * Se qvete problemi, **controllate la sezione |
- | + | ===== Step 3. Primo avvio di Magic Lantern ===== | |
- | ===== Step 3. Magic Lantern | + | * Reimpostate le vostre preferenze dal menu Canon. |
- | * Go to Canon menus and restore your preferences. Don't forget these: | + | * Con 550D/ |
- | * On 550D/ | + | * con 5D Mark II e 50D, abilitate scatto in LiveView. |
- | * On 5D Mark II and 50D, enable | + | * Eventualmente reinstallare |
- | * You may also have to re-install your custom | + | * In LiveView, |
- | * In LiveView, | + | * Premere il tasto **CESTINO** per aprire il menu di ML e **LEGGERE IL TESTO DI AIUTO** che appare. |
- | * Press the **DELETE** button to open ML menu and **READ THE HELP TEXT** that pops up. | + | * Leggete la [[userguide|Guida Utente]] e cominciate ad usare Magic Lantern. |
- | * Read the [[userguide|User Guide]] and start using Magic Lantern. | + | * **Non dimenticate di attendere per la conferma |
- | * **Don't forget to wait for LED confirmation before removing the card!** (unless you use a 550D) | + | |
====== Installing Magic Lantern on other cards ====== | ====== Installing Magic Lantern on other cards ====== | ||
{{ : | {{ : | ||
Line 100: | Line 97: | ||
* Check the [[https:// | * Check the [[https:// | ||
- | ====== | + | ====== |
- | + | ||
- | * **After opening the card door, always wait for LED confirmation (or for 5 seconds) before removing the card!!!** (no such problem on 550D) | + | |
- | * **[[http:// | + | |
- | * If you have a bootable card and have the '' | + | |
- | * If you encounter a " | + | |
- | * When in doubt, remove the battery and reboot. | + | |
- | * **And, remember that this software can damage or destroy your camera.** | + | |
+ | * **Dopo aver aperto lo sportello della scheda, attendi sempre la conferma LED (o per 5 secondi) prima di rimuovere la scheda!!!** (non necessario con 550D) | ||
+ | * **[[http:// | ||
+ | * Se hai una scheda SD avviabile e la '' | ||
+ | * Se ti capita di avere la fotocamera bloccata, **rimuovi la batteria al più presto**. | ||
+ | * Se in dubbio, rimuovi la batteria e riavvia. | ||
+ | * **E ricorda che questo software può danneggiare o distruggere la tua macchina fotografica.** |
it/install.txt · Last modified: 2012/09/05 09:57 by luix90